• Shipping to 80+ countries
  • Request a Quote
  • Tall-Frame Vacuum Packer

    GD8-ZK100 Automatic Vacuum Bag Packing Machine (P32)

    The P32 is the same GD8-ZK100 platform as the P29, rebuilt in a taller frame. Packing capacity, bag size, power and controls are unchanged: 2,500 to 3,500 pre-made pouches per hour with robotic bag pick-up, automatic opening, dosing, date printing, vacuum and impulse sealing. What changes is the working height — 3,700 mm tall against 2,080 mm — which gives headroom at the vacuum station and an elevated infeed, so the machine can sit at the end of a raised line without an extra lifting conveyor.

    2500–3500Packs per hour
    4700mm machine length
    3700mm machine height
    1500kg machine weight
    Overview

    The Same Output Platform in a Taller, Higher-Infeed Frame

    Frame height is a layout decision, not a performance one. These three points explain when the taller build is the right choice.

    Elevated Infeed

    The infeed sits higher, so product arriving from an overhead feeder, weigher or conveyor can drop straight in without an additional lifting station.

    Headroom at the Vacuum Station

    Extra height above the vacuum and sealing stations makes service access and tool changes easier on a busy line.

    Same Cycle, Same Output

    Bag pick-up, opening, dosing, vacuum, date printing and impulse sealing work exactly as on the P29, at the same 2,500 to 3,500 pouches per hour.

    Technical Data

    GD8-ZK100 P32 Technical Data

    Figures are taken directly from the machine datasheet. Utilities must be available at the installation point.

    Technical specifications of the GD8-ZK100 P32 automatic bag-feeding vacuum packaging machine
    ParameterGD8-ZK100 (P32)
    Packing capacity2500–3500 packs per hour
    Bag sizeLength ≤ 200 mm, width ≤ 105 mm
    Sealing formInstant heat sealing applied after vacuum
    Supply380V three-phase four-wire, 50 Hz
    Power12.5 kW
    Compressed air0.6–0.8 MPa, flow 0.2 m³/min
    Dimensions (L × W × H)4700 × 2965 × 3700 mm
    Machine weight1500 kg
    ControlPLC with human machine interface, full machine monitoring
    Dosing optionsLiquid and paste filler, multi-head weigher for powder and bulk, automatic feeder for block product
    AutomationAutomatic bag pick-up, opening, date and batch printing, filling, vacuum and sealing
    Abnormal condition handlingEmpty bag and missed bag detection with alarm output and withholding of product and seal

    Frame height, infeed height and discharge height are specified with the order. Confirm the available headroom in the room and the height of the upstream equipment before production.

    Exclusive to This Model

    P29 and P32 Compared Station by Station

    The two configurations share one platform. The table shows exactly where they differ and where they do not.

    Comparison of the GD8-ZK100 P29 and P32 vacuum packaging machine configurations
    AspectGD8-ZK100 P29GD8-ZK100 P32
    PlatformIdentical GD8-ZK100 rotary bag-feeding vacuum packer
    Packing capacity2500–3500 packs/h2500–3500 packs/h
    Bag type and sizePre-made pouch, length ≤ 200 mm, width ≤ 105 mm
    Cycle stationsBag pick-up, opening, dosing, top-up, date print, vacuum, impulse seal, discharge
    Vacuum level and dwellSet on the HMI and stored with the product recipe
    Machine length3540 mm4700 mm
    Machine height2080 mm3700 mm
    Machine width2965 mm2965 mm
    Weight1500 kg1500 kg
    Power and air12.5 kW at 380V three-phase four-wire, 0.6–0.8 MPa at 0.2 m³/min
    Dosing optionsLiquid and paste filler, multi-head weigher, automatic feeder for block product
    Where it suitsRooms with limited headroom and floor-mounted infeedRaised lines, overhead feeders and tall service access

    Only the frame geometry differs: the taller P32 occupies more length and height while keeping the same capacity, bag range and utilities as the P29.

    Advantages

    What the Taller Frame Gives Your Line

    Height is not decoration when the machine has to meet the equipment around it.

    Meets a Raised Line

    Connects to an elevated infeed conveyor without a separate lift, keeping the line footprint smaller.

    Service Access

    More room above the vacuum and sealing stations makes routine inspection and component changes quicker.

    Unchanged Output

    Capacity, bag range and utilities are identical to the P29, so the choice is purely about layout.

    Recipe Consistency

    The same stored recipes for dosing, vacuum and sealing transfer directly between the two frames.

    Key Numbers

    P32 Output and Dimensions

    Four figures that describe the taller configuration.

    3500packs/hMaximum output
    4700mmMachine length
    3700mmMachine height
    12.5kWInstalled power
    Applications

    Elevated Lines and Tall Infeed Setups

    The P32 is chosen where the machine has to fit the room and the line rather than the other way round.

    • Lines fed from aboveWhere product arrives from an overhead weigher, bucket elevator or feeder and can drop directly into the pouch filling station.
    • Rooms with raised platformsSites built around mezzanine or platform access, where a low frame would force an awkward transfer.
    • High-throughput tailsEnd-of-line packing stations where the machine sits downstream of a fast preparation line and must match its height.
    • Maintenance-critical productionSites that want the vacuum and sealing stations easy to reach for routine service during planned stops.
    GD8-ZK100 P32 vacuum packaging machine with tall frame
    The taller frame raises the infeed and adds headroom at the vacuum station.
    Supply and Cover

    What Is Included Before and After Delivery

    The machine is run in the factory, then supported through installation and beyond.

    Factory Test Run

    The assembled machine is operated before dispatch, and the crated frame is prepared for sea or road freight.

    Spare Parts Kit

    Gripper, suction and seal components are included and can be replenished by air express.

    12-Month Warranty

    Major parts are replaced within the warranty period, with support continuing afterwards.

    Training Material

    Operation, recipe change, cleaning and routine maintenance are covered in writing and on video.

    • Layout checkSend the room plan and we will confirm that the 3,700 mm height and 4,700 mm length suit your building.
    • Infeed matchingGive us the height of the upstream equipment and the infeed will be set to suit it.
    • Volume termsAgreed per order against quantity and destination — send your target volume and port.
    • Pouch trialSend sample pouches and product and we will confirm the filling method and vacuum settings.
    FAQ

    GD8-ZK100 P32 Questions

    Both are the GD8-ZK100 platform, so packing capacity, bag size, power, compressed air and control are identical at 2,500 to 3,500 pouches per hour. The difference is the frame: the P32 is 4,700 mm long and 3,700 mm high against 3,540 mm and 2,080 mm on the P29.

    Height and an elevated infeed matter when the machine sits at the end of a raised line, when product arrives from an overhead weigher or feeder, or when the vacuum station needs more headroom for service access. The taller frame avoids adding a separate lifting conveyor.

    Pre-made pouches up to 200 mm long and 105 mm wide, the same range as the P29. Send a sample pouch and we will confirm the magazine and gripper before the machine is built.

    Yes. The platform accepts a liquid and paste filler, a multi-head weigher for powder and bulk, or an automatic feeder for block product, so both frames cover the same product types.

    A PLC with a human machine interface runs the whole cycle and monitors the machine. Recipes for dosing, vacuum and sealing are stored on the interface, and abnormal conditions produce an alarm output.

    None. Both use impulse heat sealing applied after the vacuum is drawn, and both set vacuum level and evacuation dwell on the interface per product recipe, confirmed during the sample trial.

    The machine is assembled and run before dispatch. Installation guidance, operator training material, a spare parts kit, a 12-month warranty on major parts and lifetime online technical support are included.

    Related Models

    Compare P29 and the HLGD Unit

    If the taller frame is not needed, or the product is a brined solid, these machines are the alternatives.

    Next Step

    Confirm the P32 Against Your Layout

    Send the room plan, the pouch sample and the height of the equipment upstream. We will confirm the infeed height, the filling structure and the vacuum recipe, then prepare a quotation for the machine and the stations around it.

    How We Confirm Fit

    • Reply within 12 working hours
    • Headroom and room height checked against the frame
    • Infeed height matched to upstream equipment
    • Spare parts kit and lifetime support
    Get Quote